Related Questions
What is the correct answer?
4
A ________ topology describes how devices communicate with each other.
What is the correct answer?
4
With a crossover cable, which pins are crossed over?
What is the correct answer?
4
RIP generates routing updates every _________ seconds.
What is the correct answer?
4
You are at User EXEC mode and type the letter e. What message appears?
C. % Unknown command or computer name
D. % Invalid input detected at '^'.
What is the correct answer?
4
Which would you use to move your cursor back one word?
What is the correct answer?
4
Which of the following situations are best for DDR connections?
A. Primary WAN connection
B. A lot of constant traffic
What is the correct answer?
4
You have a total of five routers. ________ circuits are required to fully mesh the network, where every router needs ___________ interfaces.
What is the correct answer?
4
___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.
What is the correct answer?
4
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
A. TFTP server IP address
What is the correct answer?
4
Which VTP mode(s) will propagate VTP messages?
C. Client, server, and transparent
What is the correct answer?
4
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.
What is the correct answer?
4
During the learning function, the switch places addresses and ports in a(n) _________ table.
What is the correct answer?
4
________ topologies in NBMA environments do not have problems with split horizon.
What is the correct answer?
4
When choosing a dynamic routing protocol, which of the following should not be considered?
B. How routing information is shared
C. How routing information is processed
D. Number of PCs in the network
What is the correct answer?
4
Extended IP ACLs should be placed as close to the ____________ device as possible.
What is the correct answer?
4
Which controller command specifies how ones and zeros are represented on a digital circuit?
What is the correct answer?
4
You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?
A. 255.255.255.128 and 255.255.255.192
B. 255.255.255.224 and 255.255.255.240
C. 255.255.255.192 and 255.255.255.224
What is the correct answer?
4
When a carrier experiences congestion, it marks the _______ bit in the header of the Frame Relay frame.
What is the correct answer?
4
Which interface type is used to connect to the serial interface of a router?
What is the correct answer?
4
191.75.39.24 is a Class __________ address.
What is the correct answer?
4
Which of the following commands belongs on the physical interface when using dialer profiles?
What is the correct answer?
4
Which command activates an IP ACL on a router's interface?
What is the correct answer?
4
Which of the following is not an advantage of route summarization?
A. It requires less memory and processing.
B. It supports smaller routing update sizes.
C. It contains network problems.
D. It supports discontiguous subnets.
What is the correct answer?
4
Which command takes you from Privilege EXEC mode to User EXEC mode?
What is the correct answer?
4
With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.
What is the correct answer?
4
Which control sequence moves the cursor to the end of the line?
What is the correct answer?
4
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
What is the correct answer?
4
What command assigns a User EXEC password to a 2950 switch?
What is the correct answer?
4
Which type of routing protocol uses the Shortest Path First algorithm?
What is the correct answer?
4
When connecting a router to a PC, use a __________ cable.