When using debug with PAP, which of the following message types might you see?
AUTH-ACK
SUCCESS
CHALLENGE
None of these
Correct Answer :
A. AUTH-ACK
Related Questions
Which router command would take you back to a suspended telnet session?
reconnect
connect
resume
toggle
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
Delay
Reliability
Load
Bandwidth
A ___________ in a bit position of a wildcard mask means that the same bit position in the condition address must match the same bit position in the wildcard mask in order to execute the ACL's action.
0
1
10
11
__________ states that if a neighboring router sends a route to a router, the receiving router will not propagate this route back to the advertising router on the same interface.
Split horizon
Poison reverse
Hold-down timer
Hop count limit
When choosing a dynamic routing protocol, which of the following should not be considered?
Metrics used
How routing information is shared
How routing information is processed
Number of PCs in the network
191.75.39.24 is a Class __________ address.
A
B
C
None of the above
Frames sent above the __________ limit will have their _________ bit set.
CIR, DE
BC, DE
BC, FECN
CIR, FECN
Which of the following is a private address?
192.169.7.17
172.32.28.39
10.1.256.8
172.16.255.89
What command activates the IP routing process?
router
enable
network
no shutdown
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI
Which type of traffic is sent to a group of devices?
Multicast
Unicast
Broadcast
Groupcast
An OSPF's router ID is based on __________.
The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
A _________ routes between different autonomous systems.
BPG
EGP
IPP
IGP
Which of the following WAN categories does ISDN fall under?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
The 1900 switch supports ________ VLANs.
10
32
64
250
You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?
255.255.255.128 and 255.255.255.192
255.255.255.224 and 255.255.255.240
255.255.255.192 and 255.255.255.224
None of these
When choosing a WAN solution, consider all of the following except __________.
Number of devices
Cost-effectiveness
Availability
Amount of bandwidth
_________ allows you to create this summarization: 10.0.0.0/7.
Subnetting
CDR
Supernetting
VLSM
Extended IP ACLs should be placed as close to the ____________ device as possible.
Source
Destination
Which command is used to define the local addresses that are statically translated to global addresses?
ip nat inside source static
ip nat inside
ip nat inside source list
ip nat pool
To recall a previous command, which of the following would you use?
CTRL-P
ctrl-n
ctrl-r
down arrow
A _________ connects two or more LANs in the same geographic area.
LAN
WAN
MAN
SAN
Which of the following is stored in ROM? (Choose all correct answers.)
POST
ROMMON
Configuration file
System recovery file
VLSM allows you to summarize __________ back to the class boundary.
Subnets
Networks
With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.
Store-and-forward
Cut-through
Fragment-free
Runtless
Which of the following is true concerning ACLs?
Order of the statements is automatic.
All statements are processed.
If no match is found, the packet is permitted.
You can delete a specific statement in a named list.
An _____________ is a public IP address associated with an inside device.
Inside global IP address
Inside local IP address
Outside global IP address
Outside local IP address
Which Frame Relay command is used to manually resolve addresses?
frame-relay interface-dlci
frame-relay map
frame-relay resolve
frame-relay lmi-type
If the 1900 SYSTEM LED is _________, a system POST test has failed.
Green
Amber
Flashing amber
Flashing green and amber
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.
True
False