RIP has a maximum hop count of ____________ hops.
10
15
16
100
Correct Answer :
B. 15
Related Questions
Which Frame Relay command is used to manually resolve addresses?
frame-relay interface-dlci
frame-relay map
frame-relay resolve
frame-relay lmi-type
Which of the following reasons might you need to use address translation?
You have to use public addressing because your ISP didn't assign you enough private addresses.
You are using private addresses but have changed ISPs, and your new ISP won't support these private addresses.
You want to assign the same IP address to multiple machines so that users on the Internet see this offered service as a single logical computer.
You are merging two companies that use different address spaces.
Which of the following is the most expensive type of WAN connection?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
Which command takes you from Privilege EXEC mode to User EXEC mode?
enable
disable
exit
logout
When configuring your terminal emulation software for a console connection, set the flow control to __________.
Hardware
Software
None
When choosing a dynamic routing protocol, which of the following should not be considered?
Metrics used
How routing information is shared
How routing information is processed
Number of PCs in the network
Which of the following is false concerning CHAP?
It sends an encrypted password.
It sends a challenge.
It is more secure than PAP.
It uses a three-way handshake.
You are given a class C network, 192.168.1.0/24. You need one network with 120 hosts and three networks with 60 hosts. What subnet mask values would you use?
255.255.255.128 and 255.255.255.192
255.255.255.128
255.255.255.192
None of these
Which of the following is true concerning ACLs?
Order of the statements is automatic.
All statements are processed.
If no match is found, the packet is permitted.
You can delete a specific statement in a named list.
Which is an example of a hybrid protocol?
IGRP
EIGRP
RIPv1
OSPF
A _________ uses Gigabit Ethernet as a media type
WAN
LAN
MAN
LAN and MAN
You are given a Class C network with 25 bits of networking. How many subnets do you have?
1
2
3
4
Which of the following WAN categories does ISDN fall under?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
Ethernet ___________ has/have both a physical and logical bus topology.
10BaseT
10Base2 and 10Base5
10BaseT and 10Base2
10BaseT, 10Base2, and 10Base5
You have a total of five routers. ________ circuits are required to fully mesh the network, where every router needs ___________ interfaces.
5, 5
8, 4
10, 5
10, 4
Choose the following that a standard IP ACL can match on.
Destination address
IP protocol
IP protocol information
None of the above
Which of the following is true concerning full-duplexing?
It can either send or receive frames, but not both simultaneously.
It can be used with hubs.
It can be used with 10Base5 cabling.
It uses point-to-point connections.
Private addressing is defined in RFC ______.
1920
1934
1818
1918
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI
IOS images can be loaded from all the following except:
ROM
Flash
NVRAM
TFTP
What must you do to enable IP routing on your router? (Choose all of the correct answers.)
Enable the routing protocol.
Set clocking on all serial interfaces.
Assign IP addresses to your router's interfaces.
Assign the bandwidth parameter to your serial interfaces
Which of the following is true concerning RIPv2?
It uses triggered updates.
It uses broadcasts.
It is classful.
It doesn't support route summarization
_________ describe(s) users working from home.
SOHO
Branch office
Regional office
Corporate office
What command assigns a User EXEC password to a 2950 switch?
password
login
enable password
enable password level
RIP generates routing updates every _________ seconds.
15
30
60
90
OSPF hellos are sent every __________ seconds on a multi-access medium.
5
10
15
40
An _____________ is a public IP address associated with an inside device.
Inside global IP address
Inside local IP address
Outside global IP address
Outside local IP address
During the learning function, the switch places addresses and ports in a(n) _________ table.
IP address
learning
CAM
memory
Which of the following is false concerning OSPF?
It provides a loop-free topology.
It is a classful protocol and allows for a hierarchical design.
It requires more memory and processing cycles than distance vector protocols.
It is complex to configure and difficult to troubleshoot.
You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)
CTRL-Z
end
exit
logout