Which of the following trunking methods is/are proprietary to Cisco?
802.1Q
802.10
LANE
ISL
Correct Answer :
B. 802.10
Related Questions
Enter the wildcard mask value to match on every bit position in an address: _________.
255.0.0.0
0.0.0.0
255.255.255.255
255.255.0.0
Which of the following is not an advantage of DHCP?
It allows for the use of private addressing.
It reduces the amount of configuration on devices.
It reduces likelihood of configuration errors.
It gives you more control by centralizing IP addressing information.
A ___________ is basically all of the components, hardware and software, involved
in connecting computers across small and large distances.
LAN
WAN
Network
SAN
Which of the following commands belongs on the physical interface when using dialer profiles?
dialer pool-member
dialer-group
ip address
dialer string
Which of the following is true concerning full-duplexing?
It can either send or receive frames, but not both simultaneously.
It can be used with hubs.
It can be used with 10Base5 cabling.
It uses point-to-point connections.
When connecting a switch to a router, use a ___________ cable.
Crossover
Straight-through
Rollover
___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.
Q.931
Q.921
I.921
I.931
IGRP generates an update every ___________ seconds.
30
60
90
120
If you see a VC with an inactive status, this indicates ____________.
The connection between both Frame Relay DTEs is up and operational.
The connection between your Frame Relay DTE and DCE is up and operational, but there is something wrong with connection between your connected Frame Relay switch and the destination DTE.
You are not receiving any LMI messages from the Frame Relay switch.
A VTP server switch generates a summary advertisement every _________ minutes.
1
2
3
5
When choosing a WAN solution, consider all of the following except __________.
Number of devices
Cost-effectiveness
Availability
Amount of bandwidth
Which 2950 command assigns a VLAN to an interface?
vlan-membership static
vlan
switchport access vlan
switchport mode access
Which Frame Relay command is used to manually resolve addresses?
frame-relay interface-dlci
frame-relay map
frame-relay resolve
frame-relay lmi-type
Your router is running RIP and OSPF and both routing protocols are learning 192.168.1.0/24. Which routing protocol will your router use for this route?
RIP
OSPF
What command creates a DHCP address pool on a router?
ip dhcp
ip pool dhcp
ip dhcp pool network
ip dhcp pool
Which of the following is true concerning RIPv2?
It uses triggered updates.
It uses broadcasts.
It is classful.
It doesn't support route summarization
When examining the IP routing table, an EIGRP route will be shown as what letter?
I
E
O
D
_________ is/are a routed protocol.
RIP
OSPF
Both RIP and OSPF
Neither RIP or OSPF
Which control sequence moves the cursor to the end of the line?
CTRL-A
ctrl-p
ctrl-e
ctrl-z
_________ has a physical star topology but a logical ring topology.
FDDI
Token Ring
Ethernet
FDDI and Token Ring
A _________ connects two or more LANs in the same geographic area.
LAN
WAN
MAN
SAN
EIGRP uses the _________ algorithm to update its routing table.
Bellman-Ford
Dijkstra
DUAL
Integrated
How many steps do LCP and NCP go through when setting up a connection?
1
2
3
4
When a carrier experiences congestion, it marks the _______ bit in the header of the Frame Relay frame.
CIR
DE
BECN
FECN
OSPF supports a ________-layer hierarchical design.
1
2
3
Multi
When using the show interfaces command, which Frame Relay information can you not see?
The DLCI number used for LMI
The number of LMIs sent and received
Statuses of PVCs
The LMI type
Which interface type is used to connect to the serial interface of a router?
EIA/TIA-232
V.35
DB-60
X.21
Which of the following is the most expensive type of WAN connection?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?
/24, /25, and /26
/25, /26, and /27
/26, /27, and /28
None of these
When configuring your terminal emulation software for a console connection, set the flow control to __________.
Hardware
Software
None