An architect often relies on a ________ to complete the set of technical drawings used in the design of an office building.
Technical illustrator
Artist
Drafter
Construction superintendent
Correct Answer :
C. Drafter
Related Questions
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
Foreshortened
Parallel
Orthographic
Oblique
In architectural drawing ________ are often used to illustrate and detail structural components.
Foundation beam detail sections
Wall sections
Building sections
All of the above
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
Amplifier tubes
Electron tubes
Signal relays
Switches
Perspective drawings are classified according to their number of these features:
Station points
Picture planes
Vanishing points
Ground lines
The standard number of threads per inch for various diameters is the:
Series of thread
Lead
Major diameter
Thread pitch
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
Client
CAD trainee
Receptionist
Checker
The top, front, and bottom views align in this manner:
Horizontally
Vertically
According to the planar views
Parallel to the frontal plane
This type of structural steel drawing shows all dimensions necessary for fabrication:
Shop drawings
Design drawings
Weldment drawings
Application drawings
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
Circular
Elliptical
Lengthened
Angular
These maps are used to plan construction projects that locate construction features so they fit the topography of the area:
Subdivision plats
Landscape maps
Structural topography maps
Structure location plans
These breaks are used to shorten the view of an object:
Section breaks
Aligned breaks
Conventional breaks
Full breaks
Once a drawing is determined to be complete, the title block is used to document the change from:
A draft to a finished drawing
A finished to a working drawing
An assembly to a finished drawing
A working drawing to a draft
The first step in creating a traditional technical drawing is to ________.
Draw a series of guide lines
Set up the meter line
Align the paper so that it will be positioned square to the parallel bar
Sharpen the leads in the technical pens
A partial auxiliary view usually shows only features on the ________ of the inclined line and not any projection of other planes.
Hidden lines
Plane
Center lines
None of the above
In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:
Auxiliary drawings
Assembly sections
3D assemblies
Parts lists
The architectural drafter usually begins a set of working drawings by creating the ________ plan first.
Foundation
Floor plan
Elevations
Building section
If a plane is parallel to the plane of projection, it appears:
True size
As a line or edge
Foreshortened
As an oblique surface
A round is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
The type of line that projects from an object for the express purpose of locating a dimension is a ________ line.
Visible
Hidden
Extension
Dimension
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
Rotate the snap grid to the same angle of the inclined plane
Offset the right vertical line of the front view
Rotate the top line of the front view 45 degrees
Offset the top line of the front view 2 inches
Technical drawings typically serve one of three purposes:
Visualization, Communication, or Documentation
Visualization, Dimensioning, or Documentation
Communication, Documentation, or Installation
Documentation, Installation, or Engineering
This is a line terminated by arrowheads, indicating the direction and extent of a dimension:
Dimension line
Extension line
Arrowhead line
Centerline
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
Primary
Secondary
Revolved
Successive
Which of the following is one of the basic types of welded joints:
T-joint
Rear joint
Angle joint
Groove joint
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
Front
Top
Right
Back
The most common geometric form used in gears today is this:
Involute profile
Convolute profile
Base circle
Spur circle
The ________ is a standard element of a section view in a technical drawing.
Cutting Plane line
Section lines
Material hatch pattern
All of the above
This is an angled surface used on cylinders to make them easier to handle:
Fillet
Taper
Chamfer
Lug
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
Right to left and top to bottom
Right to left and bottom to top
Left to right and top to bottom
Left to right and bottom to top