How many steps do LCP and NCP go through when setting up a connection?
1
2
3
4
Correct Answer :
C. 3
Related Questions
RIP supports load balancing for up to __________ ___________ paths.
Six, unequal-cost
Four, unequal-cost
Four, equal-cost
Six, equal-cost
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
SAN
LAN
CN
SAN and CN
The function of the MODE button is to __________.
Change the status of the ports
Affect what the SYSTEM and RPS LEDs represent
Affect what the port LEDs represent
Change the status of all the LEDs
Which 1900 command enables port security?
port security
switchport security
port secure
switchport port-security
A ___________ is similar to a telephone circuit-switched connection.
PVC
SVC
IOS images can be loaded from all the following except:
ROM
Flash
NVRAM
TFTP
You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?
255.255.255.128 and 255.255.255.192
255.255.255.224 and 255.255.255.240
255.255.255.192 and 255.255.255.224
None of these
The address of a Frame Relay VC is called a ___________.
Data link layer connection identifier
Data layer connection index
Data link connection index
Data link connection identifier
_________ negotiates the data link and network layer protocols that will traverse a PPP connection.
LCP
NCP
CDP
PAP
When using debug with PAP, which of the following message types might you see?
AUTH-ACK
SUCCESS
CHALLENGE
None of these
You are given the following addressing information: 10.0.8.0/22. What type of address is this?
Network
Directed Broadcast
Host
You have this binary value: 11000001. This equates to _____ in decimal.
183
193
173
203
A __________ topology uses a single connection to connect all devices together.
Bus
Star
Point-to-point
Ring
When configuring your terminal emulation software for a console connection, set the flow control to __________.
Hardware
Software
None
An _____________ is a public IP address associated with an inside device.
Inside global IP address
Inside local IP address
Outside global IP address
Outside local IP address
BPDU stands for ____________.
Bridge Protocol Description Unicast
Bridge Protocol Data Unit
Bridge Protocol Description Unit
Bridge Protocol Data Unicast
Extended IP ACLs should be placed as close to the ____________ device as possible.
Source
Destination
Which of the following reasons might you need to use address translation?
You have to use public addressing because your ISP didn't assign you enough private addresses.
You are using private addresses but have changed ISPs, and your new ISP won't support these private addresses.
You want to assign the same IP address to multiple machines so that users on the Internet see this offered service as a single logical computer.
You are merging two companies that use different address spaces.
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI
___________ has both physical and logical ring topologies.
Ethernet
FDDI
Token Ring
__________ states that if a neighboring router sends a route to a router, the receiving router will not propagate this route back to the advertising router on the same interface.
Split horizon
Poison reverse
Hold-down timer
Hop count limit
The default encapsulation on a synchronous serial interface is _________.
HDLC
PPP
Neither HDLC nor PPP
_________ defines how the Frame Relay DTE and DCE interact with each other.
DLCI
CIR
LMI
PMI
When setting up an RJ-45 console connection, you need a RJ-45-to-DB-9 __________ adapter to attach to the COM port of your PC.
Auxiliary
Console
Connection
Terminal
Which of the following is true concerning ISL?
It is supported on both the 1900 and 2950 switches.
It adds a 26-byte trailer and 4-byte header.
Tagging is done in software.
The original Ethernet frame is not modified.
A routing protocol will use a _________ to determine which path is the best path.
Administrative distance
Metric
Hop count
Cost
When connecting a router to a PC, use a __________ cable.
Crossover
Straight-through
Rollover
A _________ connects two or more LANs in the same geographic area.
LAN
WAN
MAN
SAN
A _________ looks at OSI Reference Model layers 4-7 to make intelligent decisions about how to obtain information for a user.
SAN
LAN
CN
SAN and CN
When using the show interfaces command, which Frame Relay information can you not see?
The DLCI number used for LMI
The number of LMIs sent and received
Statuses of PVCs
The LMI type