Related Questions
What is the correct answer?
4
VLSM allows a network segment to have more than one subnet mask.
What is the correct answer?
4
EIGRP uses the _________ algorithm to update its routing table.
What is the correct answer?
4
When examining the IP routing table, an EIGRP route will be shown as what letter?
What is the correct answer?
4
Which command is used to define the local addresses that are statically translated to global addresses?
A. ip nat inside source static
C. ip nat inside source list
What is the correct answer?
4
If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router
B. Tries to resolve the command to an IP address
C. Executes the closest command that it can find in its command set
What is the correct answer?
4
RIP supports load balancing for up to __________ ___________ paths.
What is the correct answer?
4
Which of the following is the most expensive type of WAN connection?
A. Dedicated circuit connection
B. Circuit-switched connection
C. Packet-switched connection
What is the correct answer?
4
An _____________ is a public IP address associated with an inside device.
A. Inside global IP address
B. Inside local IP address
C. Outside global IP address
D. Outside local IP address
What is the correct answer?
4
What uses 64 Kbps of bandwidth?
What is the correct answer?
4
With a crossover cable, which pins are crossed over?
What is the correct answer?
4
Which of the following is not true concerning TCP?
A. Provides for reliable connections
B. Uses windowing for flow control
C. Multiplexes applications
D. Is more efficient than UDP
What is the correct answer?
4
___________ only translates one (and only one) IP address to another.
What is the correct answer?
4
You are given a Class C network with a subnet mask of 255.255.255.248. How many host addresses are there on each subnet?
What is the correct answer?
4
_________ negotiates the data link and network layer protocols that will traverse a PPP connection.
What is the correct answer?
4
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.
What is the correct answer?
4
Private addressing is defined in RFC ______.
What is the correct answer?
4
Which of the following WAN categories does ISDN fall under?
A. Dedicated circuit connection
B. Circuit-switched connection
C. Packet-switched connection
What is the correct answer?
4
What would you enter to see the last few commands you entered?
What is the correct answer?
4
You are at User EXEC mode and type the letter e. What message appears?
C. % Unknown command or computer name
D. % Invalid input detected at '^'.
What is the correct answer?
4
Which of the following is a Network layer protocol for the TCP/IP protocol stack?
What is the correct answer?
4
The _________ command takes you from User EXEC mode to Privilege EXEC mode
What is the correct answer?
4
A _________ looks at OSI Reference Model layers 4-7 to make intelligent decisions about how to obtain information for a user.
What is the correct answer?
4
You have a total of five routers. ________ circuits are required to fully mesh the network, where every router needs ___________ interfaces.
What is the correct answer?
4
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
What is the correct answer?
4
How would you suspend a telnet session?
What is the correct answer?
4
Extended IP ACLs should be placed as close to the ____________ device as possible.
What is the correct answer?
4
What must you do to enable IP routing on your router? (Choose all of the correct answers.)
A. Enable the routing protocol.
B. Set clocking on all serial interfaces.
C. Assign IP addresses to your router's interfaces.
D. Assign the bandwidth parameter to your serial interfaces
What is the correct answer?
4
If you see a VC with an inactive status, this indicates ____________.
A. The connection between both Frame Relay DTEs is up and operational.
B. The connection between your Frame Relay DTE and DCE is up and operational, but there is something wrong with connection between your connected Frame Relay switch and the destination DTE.
C. You are not receiving any LMI messages from the Frame Relay switch.
What is the correct answer?
4
You examine your interfaces, and the Ethernet 0 interface status says: Ethernet 0 is up, line protocol is down. What does this indicate?
A. There is a physical layer problem.
B. There is a data link layer problem.
C. There is a network layer problem.
What is the correct answer?
4
Which of the following is true concerning bridges?
A. They switch frames in hardware.
B. They support half- and full-duplexing.
C. They support one collision domain for the entire bridge.
D. They do only store-and-forward switching.