Automatic ignition of the charge at the end of compression
Ignition induced by the passage of a spark
Ignition of the charge before the passage of flame front
Ignition induced to supplement the process of normal combustion
C. Ignition of the charge before the passage of flame front
Unsprung mass is kept minimum
Sprang mass is kept minimum
Vehicle mass is kept minimum
All of these
Step up current
Step down current
Step up voltage
Step down voltage
Seat belt
Brake
Airbag
Steering
Increases
Decreases
Remains the same
None of these
Humidity
Temperature
Vibration
Contamination
1000 volts
2000 volts
11 kilovolts
22 kilovolts
Air-fuel ratio
Air temperature
Air flow speed
Exhaust gas volume
Shock absorber
Torsion bar
Spring
Radius rod
Controls the engine's air intake volume
Reduces the engine's air intake noise
Prevents rain water from entering the engine
Prevents dust and other foreign matter from entering the engine
Geometrical shape is square
Diameter and length of piston are same
Two cylinders are placed horizontal and two vertical
Stroke length and cylinder bore are same
Absorb the energy
Dissipate the energy
Release the energy
Increase the energy
Makes chemicals by mechanical means
Uses chemical action to provide electricity
Has curved plates instead of flat plates
Does not use an electrolyte
0.74
1.00
1.12
1.19
Octane number
Performance number
Cetane number
None of these
Improves steering comfort when steering wheel is turned to effect small changes in the direction of forward motion
Allows the steering wheel to be turned by a greater amount when steering
Makes the steering more responsive
Reduces the amount of kickback for large steering angles
36.5 MJ/kg
38.5 MJ/kg
42.5 MJ/kg
45.5 MJ/kg
Cooling efficiency
Resistance to wear
Lubrication performance
None of these
A high boiling point
Low viscosity
Compatibility with rubber and metal parts
All of these
17 : 1
15 : 1
13 : 1
10 : 1
Upper bracket
Lower bracket
Tilt bracket
Steering yoke joint
Mechanically
Hydraulically
Pneumatically
None of these
Steering wheel, steering gearbox, steering shaft, tie rod, steering knuckle, front wheels
Steering wheel, steering shaft, steering gearbox, tie rod, steering knuckle, front wheels
Steering wheel, steering shaft, steering gearbox, steering knuckle, tie rod, front wheels
Steering wheel, tie rod, steering gearbox, steering shaft, steering knuckle, front wheels
Cooling efficiency
Resistance to wear
Lubrication performance
None of these
One ply layer runs diagonally one way and another layer runs diagonally the other way
All plies run parallel to one another and vertical to tyre bead
Inner tubes are always used
None of these
1-2-3-4
1-3-4-2
1-4-3-2
1-3-2-4
Reduce the amount of noise generated
Reduce the amount of sliding resistance
Can deal with movement of the suspension both vertically and in other directions
Improve the force transmission speed
Opens at T.D.C. and closes at B.D.C.
Opens at 20° before T.D.C. and closes at 35° after B.D.C.
Opens at 10° after T.D.C. and closes at 20° before B.D.C.
None of the above
Enable the pump's fault diagnosis function to operate
Warm up and lubricate the pump
Supplies a large amount of fuel and thereby creates a choke effect
Pressurise the fuel system before the engine is started
Carburettor (or throttle body) air cleaner intake manifold intake ports cylinders
Air cleaner carburettor (or throttle body) intake ports intake manifold cylinders
Air cleaner intake manifold carburettor (or throttle body) intake ports cylinders
Air cleaner carburettor (or throttle body) intake manifold intake ports cylinders
5 %
10 %
15 %
20 %