When configuring the ip nat inside source command, which parameter must you specify to perform PAT?
pat
overload
load
port
Correct Answer :
B. overload
Related Questions
Which of the following is a Network layer protocol for the TCP/IP protocol stack?
TCP
UDP
ICMP
None of these
If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router
Logs you out
Tries to resolve the command to an IP address
Executes the closest command that it can find in its command set
Makes a "beep" sound
Which controller command specifies how ones and zeros are represented on a digital circuit?
framing
linecode
clock source
interface
Which of the following is true concerning ACLs?
Order of the statements is automatic.
All statements are processed.
If no match is found, the packet is permitted.
You can delete a specific statement in a named list.
Which control sequence moves the cursor to the end of the line?
CTRL-A
ctrl-p
ctrl-e
ctrl-z
Cisco routers generate LMI enquiries every _______ seconds and a full status update every _________ seconds.
10, 60
10, 6
60, 300
15, 60
Private addressing is defined in RFC ______.
1920
1934
1818
1918
Which 1900 command enables port security?
port security
switchport security
port secure
switchport port-security
A ___________ is similar to a telephone circuit-switched connection.
PVC
SVC
When choosing a WAN solution, consider all of the following except __________.
Number of devices
Cost-effectiveness
Availability
Amount of bandwidth
VLSM allows a network segment to have more than one subnet mask.
True
False
Which router-on-a-stick command defines the VLAN for the interface?
vlan
encapsulation
trunk
frame-type
If the 2950's RPS is ________, the external power supply is supplying power.
Off
Amber
Flashing amber
Green
RIP has a maximum hop count of ____________ hops.
10
15
16
100
You execute the line console 0 command from Configuration mode. What will the router's prompt be?
Router(config)#
Router(config-line)#
Router(config-interface)#
Router#(config-if)
Which of the following trunking methods is/are proprietary to Cisco?
802.1Q
802.10
LANE
ISL
An OSPF's router ID is based on __________.
The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
Which of the following is not true concerning TCP?
Provides for reliable connections
Uses windowing for flow control
Multiplexes applications
Is more efficient than UDP
You are given the following addressing information: 172.17.16.255/23. What type of address is this?
Network
Directed Broadcast
Host
A _________ is used to connect networking devices that are in a very close geographic area, such as a floor of a building, a building itself, or a campus environment.
WAN
LAN
MAN
LAN and MAN
IOS images can be loaded from all the following except:
ROM
Flash
NVRAM
TFTP
___________ has both physical and logical ring topologies.
Ethernet
FDDI
Token Ring
Enter the wildcard mask value to match on every bit position in an address: _________.
255.0.0.0
0.0.0.0
255.255.255.255
255.255.0.0
When setting up an RJ-45 console connection, you need a RJ-45-to-DB-9 __________ adapter to attach to the COM port of your PC.
Auxiliary
Console
Connection
Terminal
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
SAN
LAN
CN
SAN and CN
RIP supports load balancing for up to __________ ___________ paths.
Six, unequal-cost
Four, unequal-cost
Four, equal-cost
Six, equal-cost
Which of the following is false concerning OSPF?
It provides a loop-free topology.
It is a classful protocol and allows for a hierarchical design.
It requires more memory and processing cycles than distance vector protocols.
It is complex to configure and difficult to troubleshoot.
Which protocol supports VLSM?
RIPv2
IGRP
RIP and IGRP
None of these
You have ISL trunks in your network and five VLANs configured. How many instances of STP are running?
1
5
10
15
Which interface type is used to connect to the serial interface of a router?
EIA/TIA-232
V.35
DB-60
X.21