What command assigns a User EXEC password to a 2950 switch?
password
login
enable password
enable password level
Correct Answer :
A. password
Related Questions
Which of the following trunking methods is/are proprietary to Cisco?
802.1Q
802.10
LANE
ISL
Which of the following is true concerning full-duplexing?
It can either send or receive frames, but not both simultaneously.
It can be used with hubs.
It can be used with 10Base5 cabling.
It uses point-to-point connections.
The function of the MODE button is to __________.
Change the status of the ports
Affect what the SYSTEM and RPS LEDs represent
Affect what the port LEDs represent
Change the status of all the LEDs
Which of the following is true concerning bridges?
They switch frames in hardware.
They support half- and full-duplexing.
They support one collision domain for the entire bridge.
They do only store-and-forward switching.
Which interface type is used to connect to the serial interface of a router?
EIA/TIA-232
V.35
DB-60
X.21
OSPF supports a ________-layer hierarchical design.
1
2
3
Multi
You execute the line console 0 command from Configuration mode. What will the router's prompt be?
Router(config)#
Router(config-line)#
Router(config-interface)#
Router#(config-if)
What command creates a DHCP address pool on a router?
ip dhcp
ip pool dhcp
ip dhcp pool network
ip dhcp pool
Which of the following is true concerning RIPv2?
It uses triggered updates.
It uses broadcasts.
It is classful.
It doesn't support route summarization
Which router-on-a-stick command defines the VLAN for the interface?
vlan
encapsulation
trunk
frame-type
Which would you use to move your cursor back one word?
ESC-B
esc-p
ctrl-b
ctrl-p
VLSM allows you to summarize __________ back to the class boundary.
Subnets
Networks
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.
True
False
Which frame field is different between ISO HDLC and Cisco's HDLC?
Address
Control
Flag
Proprietary
Which 2950 command enables trunking?
switchport mode trunk
trunking on
trunking enable
switchport trunk on
During the learning function, the switch places addresses and ports in a(n) _________ table.
IP address
learning
CAM
memory
The ___________ converts an ISDN four-wire connection to a two-wire connection.
NT5
NP1
NT1
TN1
Which command defines interesting traffic?
dialer-group
dialer-list
dialer map
dialer remote-name
Distance vector protocols use ___________ to disseminate routing information.
Unicast
Multicast
Broadcast
Which of the following is a disadvantage of SANs?
Distance limitation
Cost
Overhead
Management
What subnet mask would you use to set up a default route?
0.0.0.0
255.255.255.255
Depends on the type of network number
None of these answers
A ___________ in a bit position of a wildcard mask means that the same bit position in the condition address must match the same bit position in the wildcard mask in order to execute the ACL's action.
0
1
10
11
Which of the following is not an advantage of DHCP?
It allows for the use of private addressing.
It reduces the amount of configuration on devices.
It reduces likelihood of configuration errors.
It gives you more control by centralizing IP addressing information.
You are at User EXEC mode and type the letter e. What message appears?
% Incomplete command.
% Ambiguous command:
% Unknown command or computer name
% Invalid input detected at '^'.
With a crossover cable, which pins are crossed over?
1 and 2, 3 and 6
1 and 3, 2 and 6
1 and 4, 2 and 6
1 and 3, 4 and 6
If the port status LED on a 2950 is ________, there is a physical layer connection problem.
Flashing green and amber
Flashing green
Amber
Flashing amber
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
TFTP server IP address
Verification to copy
Source filename
Destination filename
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI
Private addressing is defined in RFC ______.
1920
1934
1818
1918
The dialer map command contains all of the following parameters except __________.
Protocol name
Remote router name
Address of local router
Speed of the connection