Related Questions
What is the correct answer?
4
When choosing a networking product, you should consider all of the following except _______.
A. Ease of installation and support
B. Product features and functions
What is the correct answer?
4
The default encapsulation on a synchronous serial interface is _________.
What is the correct answer?
4
The function of the MODE button is to __________.
A. Change the status of the ports
B. Affect what the SYSTEM and RPS LEDs represent
C. Affect what the port LEDs represent
D. Change the status of all the LEDs
What is the correct answer?
4
___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.
What is the correct answer?
4
What subnet mask would you use to set up a default route?
C. Depends on the type of network number
What is the correct answer?
4
Which is an example of a hybrid protocol?
What is the correct answer?
4
When examining the IP routing table, an EIGRP route will be shown as what letter?
What is the correct answer?
4
Which command defines interesting traffic?
What is the correct answer?
4
Which Frame Relay command is used to manually resolve addresses?
A. frame-relay interface-dlci
What is the correct answer?
4
VLSM allows you to summarize __________ back to the class boundary.
What is the correct answer?
4
Which interface type is used to connect to the serial interface of a router?
What is the correct answer?
4
Which types of memory do not maintain their contents during a power-off state?
What is the correct answer?
4
Which router command would you use to view the configuration register value?
What is the correct answer?
4
The slot number of a 1900's Fast Ethernet uplink ports is ________.
D. No slot number is used
What is the correct answer?
4
You are given a Class C network with 25 bits of networking. How many subnets do you have?
What is the correct answer?
4
You are given the following addressing information: 192.168.37.192/25. What type of address is this?
What is the correct answer?
4
Which 2950 command assigns a VLAN to an interface?
A. vlan-membership static
C. switchport access vlan
D. switchport mode access
What is the correct answer?
4
The root switch is the one elected with the __________ __________.
What is the correct answer?
4
Which control sequence moves the cursor to the end of the line?
What is the correct answer?
4
The ___________ is the point where the carrier's responsibility ends and yours begins.
What is the correct answer?
4
Frames sent above the __________ limit will have their _________ bit set.
What is the correct answer?
4
What router command saves the active configuration to NVRAM?
A. copy nvram startup-config
B. copy startup-config running-config
C. copy running-config nvram
D. copy running-config startup-config
What is the correct answer?
4
Which would you use to move your cursor back one word?
What is the correct answer?
4
When using debug with PAP, which of the following message types might you see?
What is the correct answer?
4
Which router command specifies the ISDN switch the router is connected to?
What is the correct answer?
4
You examine your interfaces, and the Ethernet 0 interface status says: Ethernet 0 is up, line protocol is down. What does this indicate?
A. There is a physical layer problem.
B. There is a data link layer problem.
C. There is a network layer problem.
What is the correct answer?
4
If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router
B. Tries to resolve the command to an IP address
C. Executes the closest command that it can find in its command set
What is the correct answer?
4
The ___________ converts an ISDN four-wire connection to a two-wire connection.
What is the correct answer?
4
Which of the following is true concerning full-duplexing?
A. It can either send or receive frames, but not both simultaneously.
B. It can be used with hubs.
C. It can be used with 10Base5 cabling.
D. It uses point-to-point connections.
What is the correct answer?
4
___________ only translates one (and only one) IP address to another.