When examining the IP routing table, an EIGRP route will be shown as what letter?

Question

When examining the IP routing table, an EIGRP route will be shown as what letter?

A. I

B. E

C. O

D. D

Correct Answer :

D. D

Share this question with your friends

Show all WAN MCQ

Comment

The root switch is the one elected with the .

Discuss this answer

When connecting a switch to a router, use a ___________ cable.

Discuss this answer

Which prompt indicates that you are at User EXEC mode?

A. >

B. #

C. %

D. @

Discuss this answer

A routing protocol that supports route summarization must perform all except which of the following?

Discuss this answer

Which would you use to move your cursor back one word?

A. ESC-B

B. esc-p

C. ctrl-b

D. ctrl-p

Discuss this answer

A _________ connects two or more LANs in the same geographic area.

A. LAN

B. WAN

C. MAN

D. SAN

Discuss this answer

You execute the line console 0 command from Configuration mode. What will the router's prompt be?

Discuss this answer

With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.

Discuss this answer

When connecting a router to a PC, use a __________ cable.

Discuss this answer

RIP has a maximum hop count of ____________ hops.

A. 10

B. 15

C. 16

D. 100

Discuss this answer

The dialer map command contains all of the following parameters except __________.

Discuss this answer

To recall a previous command, which of the following would you use?

A. CTRL-P

B. ctrl-n

C. ctrl-r

Discuss this answer

The default encapsulation on a synchronous serial interface is _________.

A. HDLC

B. PPP

Discuss this answer

What command creates a DHCP address pool on a router?

Discuss this answer

_________ allows you to create this summarization: 10.0.0.0/7.

B. CDR

D. VLSM

Discuss this answer

RIP generates routing updates every _________ seconds.

A. 15

B. 30

C. 60

D. 90

Discuss this answer

You are given the following addressing information: 172.17.16.255/23. What type of address is this?

C. Host

Discuss this answer

Enter the wildcard mask value to match on every bit position in an address: _________.

Discuss this answer

A Class A address has _________ host bits.

A. 8

B. 16

C. 20

D. 24

Discuss this answer

What router command saves the active configuration to NVRAM?

Discuss this answer

Which of the following is false concerning VLANs?

Discuss this answer

_________ negotiates the data link and network layer protocols that will traverse a PPP connection.

A. LCP

B. NCP

C. CDP

D. PAP

Discuss this answer

A __________ route is the best path to reach a destination within the topology table.

Discuss this answer

___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.

A. Q.931

B. Q.921

C. I.921

D. I.931

Discuss this answer

You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?

Discuss this answer

A routing protocol will use a _________ to determine which path is the best path.

B. Metric

D. Cost

Discuss this answer

Which Frame Relay command is used to manually resolve addresses?

Discuss this answer

When using debug with PAP, which of the following message types might you see?

Discuss this answer

Which router command clears all of the static translations in the address translation table?

Discuss this answer

What command assigns a User EXEC password to a 2950 switch?

B. login

Discuss this answer

Answer 1

A. Lowest MAC address

Answer 2

B. Highest MAC address

Answer 3

C. Lowest switch ID

Answer 4

D. Highest switch ID

Answer 5

A. Crossover

Answer 6

B. Straight-through

Answer 7

C. Rollover

Answer 8

A. Carry the subnet mask with the network entry.

Answer 9

B. Make routing decisions based on the entire destination IP address.

Answer 10

C. Summarize entries so that the same lowest-order bits match.

Answer 11

D. None of these.

Answer 12

A. Router(config)#

Answer 13

B. Router(config-line)#

Answer 14

C. Router(config-interface)#

Answer 15

D. Router#(config-if)

Answer 16

A. Store-and-forward

Answer 17

B. Cut-through

Answer 18

C. Fragment-free

Answer 19

D. Runtless

Answer 20

A. Crossover

Answer 21

B. Straight-through

Answer 22

C. Rollover

Answer 23

A. Protocol name

Answer 24

B. Remote router name

Answer 25

C. Address of local router

Answer 26

D. Speed of the connection

Answer 27

D. down arrow

Answer 28

C. Neither HDLC nor PPP

Answer 29

A. ip dhcp

Answer 30

B. ip pool dhcp

Answer 31

C. ip dhcp pool network

Answer 32

D. ip dhcp pool

Answer 33

A. Subnetting

Answer 34

C. Supernetting

Answer 35

A. Network

Answer 36

B. Directed Broadcast

Answer 37

A. 255.0.0.0

Answer 38

B. 0.0.0.0

Answer 39

C. 255.255.255.255

Answer 40

D. 255.255.0.0

Answer 41

A. copy nvram startup-config

Answer 42

B. copy startup-config running-config

Answer 43

C. copy running-config nvram

Answer 44

D. copy running-config startup-config

Answer 45

A. A VLAN is a broadcast domain.

Answer 46

B. A VLAN is a logical group of users.

Answer 47

C. A VLAN is location-dependent.

Answer 48

D. A VLAN is a subnet.

Answer 49

A. Successor

Answer 50

B. Feasible successor

Answer 51

C. Advertised distance

Answer 52

D. Feasible distance

Answer 53

A. /24, /25, and /26

Answer 54

B. /25, /26, and /27

Answer 55

C. /26, /27, and /28

Answer 56

D. None of these

Answer 57

A. Administrative distance

Answer 58

C. Hop count

Answer 59

A. frame-relay interface-dlci

Answer 60

B. frame-relay map

Answer 61

C. frame-relay resolve

Answer 62

D. frame-relay lmi-type

Answer 63

A. AUTH-ACK

Answer 64

B. SUCCESS

Answer 65

C. CHALLENGE

Answer 66

D. None of these

Answer 67

A. erase ip nat translation *

Answer 68

B. clear ip nat translation *

Answer 69

C. clear ip nat translation all

Answer 70

D. None of these commands

Answer 71

A. password

Answer 72

C. enable password

Answer 73

D. enable password level

When examining the IP routing table, an EIGRP route will be shown as what letter?

Correct Answer :

Show all WAN MCQ

Related Questions

The root switch is the one elected with the .

When connecting a switch to a router, use a ___________ cable.

Which prompt indicates that you are at User EXEC mode?

A routing protocol that supports route summarization must perform all except which of the following?

Which would you use to move your cursor back one word?

A _________ connects two or more LANs in the same geographic area.

You execute the line console 0 command from Configuration mode. What will the router's prompt be?

With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.

When connecting a router to a PC, use a __________ cable.

RIP has a maximum hop count of ____________ hops.

The dialer map command contains all of the following parameters except __________.

To recall a previous command, which of the following would you use?

The default encapsulation on a synchronous serial interface is _________.

What command creates a DHCP address pool on a router?

_________ allows you to create this summarization: 10.0.0.0/7.

RIP generates routing updates every _________ seconds.

You are given the following addressing information: 172.17.16.255/23. What type of address is this?

Enter the wildcard mask value to match on every bit position in an address: _________.

A Class A address has _________ host bits.

What router command saves the active configuration to NVRAM?

Which of the following is false concerning VLANs?

_________ negotiates the data link and network layer protocols that will traverse a PPP connection.

A __________ route is the best path to reach a destination within the topology table.

___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.

You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?

A routing protocol will use a _________ to determine which path is the best path.

Which Frame Relay command is used to manually resolve addresses?

When using debug with PAP, which of the following message types might you see?

Which router command clears all of the static translations in the address translation table?

What command assigns a User EXEC password to a 2950 switch?

Also checkout

When examining the IP routing table, an EIGRP route will be shown as what letter?

Correct Answer :

Show all WAN MCQ

Related Questions

The root switch is the one elected with the __________ __________.

When connecting a switch to a router, use a ___________ cable.

Which prompt indicates that you are at User EXEC mode?

A routing protocol that supports route summarization must perform all except which of the following?

Which would you use to move your cursor back one word?

A _________ connects two or more LANs in the same geographic area.

You execute the line console 0 command from Configuration mode. What will the router's prompt be?

With _________ switching, the switch reads the destination MAC address of the frame andimmediately starts forwarding the frame.

When connecting a router to a PC, use a __________ cable.

RIP has a maximum hop count of ____________ hops.

The dialer map command contains all of the following parameters except __________.

To recall a previous command, which of the following would you use?

The default encapsulation on a synchronous serial interface is _________.

What command creates a DHCP address pool on a router?

_________ allows you to create this summarization: 10.0.0.0/7.

RIP generates routing updates every _________ seconds.

You are given the following addressing information: 172.17.16.255/23. What type of address is this?

Enter the wildcard mask value to match on every bit position in an address: _________.

A Class A address has _________ host bits.

What router command saves the active configuration to NVRAM?

Which of the following is false concerning VLANs?

_________ negotiates the data link and network layer protocols that will traverse a PPP connection.

A __________ route is the best path to reach a destination within the topology table.

___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.

You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?

A routing protocol will use a _________ to determine which path is the best path.

Which Frame Relay command is used to manually resolve addresses?

When using debug with PAP, which of the following message types might you see?

Which router command clears all of the static translations in the address translation table?

What command assigns a User EXEC password to a 2950 switch?

Also checkout

The root switch is the one elected with the .

With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.