Related Questions
What is the correct answer?
4
This type of solid has two bases that are parallel equal polygons:
What is the correct answer?
4
A line with a tapering width can be easily created by using the __________ tool.
What is the correct answer?
4
The Offset tool should only be used for placing ________ in an isometric drawing.
What is the correct answer?
4
These gears transmit power between shafts whose axes intersect at any angle:
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
This is a curve showing the displacement of the follower as ordinates on a base line that represents one revolution of the cam:
What is the correct answer?
4
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
What is the correct answer?
4
Lines of an isometric drawing that are not parallel to the isometric axes are called this:
What is the correct answer?
4
A partial auxiliary view usually shows only features on the ________ of the inclined line and not any projection of other planes.
What is the correct answer?
4
In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
What is the correct answer?
4
The UCS icon represents the intersection of the ________.
What is the correct answer?
4
A secondary auxiliary view is a projection off of the ________.
C. Primary auxiliary view
What is the correct answer?
4
In this type of section, one quarter of the object is removed:
What is the correct answer?
4
The architectural and construction industries use the United States National CAD standard (NCS) system on many ________ projects.
What is the correct answer?
4
Placement of dimensions on a drawing is controlled by ________.
C. Corporate drafting standards
What is the correct answer?
4
The top, front, and bottom views align in this manner:
C. According to the planar views
D. Parallel to the frontal plane
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
A. Fused deposition modeling
B. Stereo lithography apparatus
D. Selective laser sintering
What is the correct answer?
4
A back or backing weld is a type of:
What is the correct answer?
4
Given a situation in which the drafter has crossed extension lines in a drawing what can be done to clean up the point of crossing?
A. Use the Modify tool to clean up the extension lines
B. Use the Tolerance tool to clean up the extension lines
C. Use the Break tool to clean up the extension lines
D. Use the stretch tool to clean up the extension lines
What is the correct answer?
4
The maximum and minimum sizes of a feature are identified by a ________ tolerance.
What is the correct answer?
4
This is formed where three or more surfaces intersect:
What is the correct answer?
4
A line drawn with a long section, short dash, and another long section is a ________.
C. Center axis of a hidden cylinder
What is the correct answer?
4
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
What is the correct answer?
4
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
What is the correct answer?
4
Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a ________.
C. Whole new set of drawings
What is the correct answer?
4
The ________ tool on the Dimension tool bar will place several dimensions at one time by using a selection box placed over several part features.
What is the correct answer?
4
Center lines are used to locate or represent the centers of ________.
What is the correct answer?
4
This is the term for the range of tightness or looseness resulting from the allowances and tolerances in mating parts:
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.