The _________ command takes you from User EXEC mode to Privilege EXEC mode
DISABLE
ENABLE
Correct Answer :
B. ENABLE
Related Questions
Which control sequence moves the cursor to the end of the line?
CTRL-A
ctrl-p
ctrl-e
ctrl-z
Which command assigns a default gateway to the 2950 switch?
(config)# default-gateway
(config-if)# default-gateway
(config-if)# ip default-gateway
(config)# ip default-gateway
An idle DDR connection will be torn down after _________ seconds of not seeing interesting traffic.
120
122
130
132
With a rollover cable, pin 7 on one end is mapped to pin ________ on the other end.
2
3
4
5
Which router-on-a-stick command defines the VLAN for the interface?
vlan
encapsulation
trunk
frame-type
Which of the following is the most expensive type of WAN connection?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
Choose the following that a standard IP ACL can match on.
Destination address
IP protocol
IP protocol information
None of the above
If the 2950's RPS is ________, the external power supply is supplying power.
Off
Amber
Flashing amber
Green
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
SAN
LAN
CN
SAN and CN
Which frame field is different between ISO HDLC and Cisco's HDLC?
Address
Control
Flag
Proprietary
Which VTP mode(s) will propagate VTP messages?
Client and server
Server
Client, server, and transparent
Transparent
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI
Which command takes you from Privilege EXEC mode to User EXEC mode?
enable
disable
exit
logout
Which of the following is stored in ROM? (Choose all correct answers.)
POST
ROMMON
Configuration file
System recovery file
Which router command would you use to test only layer-3 connectivity?
telnet
show cdp traffic
show interfaces
traceroute
If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router
Logs you out
Tries to resolve the command to an IP address
Executes the closest command that it can find in its command set
Makes a "beep" sound
Which of the following is a valid subnet mask value?
255.0.255.255
0.0.0.255
255.255.254.0
255.255.255.256
With a crossover cable, which pins are crossed over?
1 and 2, 3 and 6
1 and 3, 2 and 6
1 and 4, 2 and 6
1 and 3, 4 and 6
Which of the following are classless protocols?
IGRP
EIGRP
IGRP and EIGRP
Neither IGRP or EIGRP
Which of the following is true concerning ACLs?
Order of the statements is automatic.
All statements are processed.
If no match is found, the packet is permitted.
You can delete a specific statement in a named list.
If the 1900 SYSTEM LED is _________, a system POST test has failed.
Green
Amber
Flashing amber
Flashing green and amber
When connecting a switch to a router, use a ___________ cable.
Crossover
Straight-through
Rollover
You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?
255.255.255.128 and 255.255.255.192
255.255.255.224 and 255.255.255.240
255.255.255.192 and 255.255.255.224
None of these
A _________ routes between different autonomous systems.
BPG
EGP
IPP
IGP
RIP has a hold-down period of ____________ seconds.
60
120
180
280
You are given a class C network, 192.168.1.0/24. You need one network with 120 hosts and three networks with 60 hosts. What subnet mask values would you use?
255.255.255.128 and 255.255.255.192
255.255.255.128
255.255.255.192
None of these
EIGRP will route for ___________.
IP
IP and IPX
IP and AppleTalk
IP, IPX, and AppleTalk
RIP supports load balancing for up to __________ ___________ paths.
Six, unequal-cost
Four, unequal-cost
Four, equal-cost
Six, equal-cost
Which of the following reasons might you need to use address translation?
You have to use public addressing because your ISP didn't assign you enough private addresses.
You are using private addresses but have changed ISPs, and your new ISP won't support these private addresses.
You want to assign the same IP address to multiple machines so that users on the Internet see this offered service as a single logical computer.
You are merging two companies that use different address spaces.
Which controller command specifies how ones and zeros are represented on a digital circuit?
framing
linecode
clock source
interface