Which of the following is stored in ROM? (Choose all correct answers.)
POST
ROMMON
Configuration file
System recovery file
Correct Answer :
A. POST
Related Questions
What must you do to enable IP routing on your router? (Choose all of the correct answers.)
Enable the routing protocol.
Set clocking on all serial interfaces.
Assign IP addresses to your router's interfaces.
Assign the bandwidth parameter to your serial interfaces
Which controller command specifies how ones and zeros are represented on a digital circuit?
framing
linecode
clock source
interface
When choosing a WAN solution, consider all of the following except __________.
Number of devices
Cost-effectiveness
Availability
Amount of bandwidth
You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)
CTRL-Z
end
exit
logout
Which 2950 command enables trunking?
switchport mode trunk
trunking on
trunking enable
switchport trunk on
Which types of memory do not maintain their contents during a power-off state?
NVRAM
ROM
RAM
Flash
Cisco routers generate LMI enquiries every _______ seconds and a full status update every _________ seconds.
10, 60
10, 6
60, 300
15, 60
If the 1900's mode is FDUP, and the LED is _________, the port speed is set to autodetect.
Green
Off
Amber
None of these
Which router-on-a-stick command defines the VLAN for the interface?
vlan
encapsulation
trunk
frame-type
Choose the following that a standard IP ACL can match on.
Destination address
IP protocol
IP protocol information
None of the above
Which of the following is true concerning 802.1Q?
It supports hub connections.
It is supported on both the 1900 and 2950 switches.
The native VLAN is tagged.
The original Ethernet frame is not modified.
What uses 64 Kbps of bandwidth?
PRI
BRI
DS1
DS0
When connecting a switch to a router, use a ___________ cable.
Crossover
Straight-through
Rollover
A _________ uses Gigabit Ethernet as a media type
WAN
LAN
MAN
LAN and MAN
PPP can do all of the following except ___________.
Authentication
Compression
Quality of Service
None of these
___________ only translates one (and only one) IP address to another.
NAT
PAT
PAR
NAT and PAT
OSPF hellos are sent every __________ seconds on a multi-access medium.
5
10
15
40
_________ defines how the Frame Relay DTE and DCE interact with each other.
DLCI
CIR
LMI
PMI
When configuring the ip nat inside source command, which parameter must you specify to perform PAT?
pat
overload
load
port
A routing protocol will use a _________ to determine which path is the best path.
Administrative distance
Metric
Hop count
Cost
When a carrier experiences congestion, it marks the _______ bit in the header of the Frame Relay frame.
CIR
DE
BECN
FECN
Which protocol supports VLSM?
RIPv2
IGRP
RIP and IGRP
None of these
Enter the wildcard mask value to match on every bit position in an address: _________.
255.0.0.0
0.0.0.0
255.255.255.255
255.255.0.0
Which router command specifies the ISDN switch the router is connected to?
isdn switch-type
isdn connection-type
isdn spid1
interface serial0:15
The ___________ is the point where the carrier's responsibility ends and yours begins.
Local loop
Demarcation point
CPE
Toll network
To recall a previous command, which of the following would you use?
CTRL-P
ctrl-n
ctrl-r
down arrow
A _________ is used to connect networking devices that are in a very close geographic area, such as a floor of a building, a building itself, or a campus environment.
WAN
LAN
MAN
LAN and MAN
Which of the following is a valid subnet mask value?
255.0.255.255
0.0.0.255
255.255.254.0
255.255.255.256
Which router command creates a standard named ACL called test?
ip access-list test
access-list test
ip access-list standard test
access-list standard test
VLSM allows you to summarize __________ back to the class boundary.
Subnets
Networks