This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
Oblique projection
Perpendicular projection
Aesthetic projection
Angular projection
Correct Answer :
A. Oblique projection
Related Questions
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
Offset
Half
Whole
Broken out
This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:
Ellipsoid
Torus
Cone
Cylinder
In isometric projection, all distances are approximately this percentage of their true size:
120 percent
80 percent
50 percent
20 percent
Objects that are symmetric can be shown effectively using this type of section:
Quarter section
Half section
Full section
Symmetric section
A fillet is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
A drafter who develops technical drawings of a highway overpass would most likely be a ________ drafter.
Architectural
Civil
Mechanical
Process piping
Most architectural drawings produced for field use by building contractors are printed on architectural D size paper which measures ________.
24 × 36
18 × 24
11 × 17
34 × 22
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
Fused deposition modeling
Stereo lithography apparatus
Solid ground curing
Selective laser sintering
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
Removed section
Revolved section
Auxiliary section
Partial section
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
Client
CAD trainee
Receptionist
Checker
When filling an area with a hatch pattern in Auto-CAD the drafter needs to be able to ________.
See the entire bounding area to hatch
Set Ortho on
Turn ISO grid off
Set the layer to Defpoints
Spur gear design normally begins with selecting this:
Rack size
Tooth size
Gear size
Pitch diameter
A half-moon protractor is divided into how many degrees?
360
180
270
310
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
Rotate the snap grid to the same angle of the inclined plane
Offset the right vertical line of the front view
Rotate the top line of the front view 45 degrees
Offset the top line of the front view 2 inches
The 3-D commands on the Modeling toolbar include ________.
Box
Sphere
Extrude
All of the above
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
Explode the dimension and then erase the center mark
Use the Properties dialog box to turn off the center mark of the dimension
It can't be done
Use the trim tool to take away the stacked center mark
In offset sections, offsets or bends in the cutting plane are all:
90 degrees
180 degrees
Either 90 or 180 degrees
30, 60 or 90 degrees
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
Primary
Secondary
Revolved
Successive
Once a drawing is determined to be complete, the title block is used to document the change from:
A draft to a finished drawing
A finished to a working drawing
An assembly to a finished drawing
A working drawing to a draft
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
This is used in applications for nonferrous construction:
Copper tubing
Steel pipe
PVC pipe
Iron tubing
These weld symbols have no arrow-side or other-side significance:
Projection or seam weld
Back or backing weld
Surface or groove weld
Flash and upset weld
This practice considers an individual part's dimensions and tolerances and that part's relation to its related parts:
Applying allowances
Geometric dimensioning and tolerancing
Creating datum references
Angular dimensioning tolerances
Using this as a communication and design review tool can help shorten the process and eliminate productivity barriers:
Development plans
Portable document files
The Internet and e-mail
Gantt charts
It is customary for the first sheet of a working drawing set to include ________.
A parts list
Exploded assembly
Assembled assembly
All of the above
When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
Horizontal
Vertical
Inclined
None of the above
This is a line terminated by arrowheads, indicating the direction and extent of a dimension:
Dimension line
Extension line
Arrowhead line
Centerline
If designs require changes, they should be documented with:
Development plans
Product proposals
Document reviews
Engineering change orders
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
1/4 = 1'-0
1/8 = 1'-0
1 = 100'
3/4 = 1'-0
In this type of drawing, vertical pipes may be revolved into the horizontal plane:
Standard view
Elevation view
Transverse piping
Developed piping