These weld symbols have no arrow-side or other-side significance:
Projection or seam weld
Back or backing weld
Surface or groove weld
Flash and upset weld
Correct Answer :
D. Flash and upset weld
Related Questions
The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
Full
Half
Quarter
None of the above
These are lines drawn on a map to locate, in the plan view, points of equal ground elevation:
Contours
Elevations
Profiles
Hatches
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
Offset
Half
Whole
Broken out
A cylinder can be created by drawing a rectangular shape then the ________ tool.
Revolve
Sweep
Extrude
None of the above
3.When lines intersect on a drawing at angles of this many degrees, it is customary not to dimension the angle:
360
180
90
45
Angles project true size only when the plane containing the angle and plane of projection are this:
Adjacent
Aligned
Perpendicular
Parallel
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
Circular
Elliptical
Lengthened
Angular
In working drawings, these show all necessary information not given directly on the drawing with its dimensions and notes:
Document strips
Portable documents
Formatting forms
Title and record strips
This is the bottom surface joining the sides of two adjacent threads:
Lead
Pitch
Crest
Root
There should be a visible gap between the wall and the ________ line.
Dimension
Extension
Center
Leader
An accurate record of changes made to release drawings is tracked via this:
A revision block
The basic title form
Working drawings
Portable documents
These are special installations of stone or concrete marking the locations of points accurately determined by precise surveying:
Topographic marks
Hatches
Monuments
Pillars
A partial auxiliary view is used to show only the ________ in the auxiliary view.
Projected inclined plane
The projected top view
The projected side view
None of the above
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
These drawings are given to contractors to perform work or manufacture individual parts:
Assembly details
3D drawings
Working drawings
Skeleton assemblies
In developing a multi-view drawing, the drafter can use a ________ line to help locate the top and right side views.
Object
Hidden
Dimension
Miter
The distance a screw thread advances axially in one turn is the:
Lead
Pitch
Turn
Crest
Traditional drafters need to be able to create several different line widths because ________.
Different line widths convey different information
The line width has to do with how dark it appear in the finished drawing
They seem to transmit better in a fax machine
It makes no difference
Most architectural firms and mechanical design companies utilize different categories of blocks. These sets of blocks are usually housed in ________.
Block vaults
Block libraries
Block books
Block references
In this type of section, one quarter of the object is removed:
Revolved section
Removed section
Quarter section
Half section
This type of solid has two bases that are parallel equal polygons:
Pyramid
Prism
Cone
Torus
These breaks are used to shorten the view of an object:
Section breaks
Aligned breaks
Conventional breaks
Full breaks
A secondary auxiliary view is a projection off of the ________.
Front view
Top view
Primary auxiliary view
None of the above
Some common blocks used by architectural drafters include ________.
Door swings
Ceiling fans
Appliances
All of the above
The site plan illustrates ________.
The floor plan
Where the house sits on the property
The roof plan
Where the garage and driveway are located
A full scale technical drawing will have a scale factor of ________.
1 : 1
1 : 2
2 : 1
1 : 4
Drawings created with commercial software are typically saved as:
Rapid prototypes
Electronic files
Draft drawings
Change orders
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?
Quarter
Half
Full
Double
Center lines are used to locate or represent the centers of ________.
Arcs
Circles
Hidden round features
All of the above
The MASSPROP shortcut will provide the following information.
Mass
Volume
Bounding box
All of the above