Related Questions
What is the correct answer?
4
This type of solid has two bases that are parallel equal polygons:
What is the correct answer?
4
When only a small section of an interior area needs to be revealed the drafter can use a ________ section.
What is the correct answer?
4
A partial auxiliary view usually shows only features on the ________ of the inclined line and not any projection of other planes.
What is the correct answer?
4
This is a common method for connecting steel members of buildings and bridges:
What is the correct answer?
4
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
The site plan illustrates ________.
B. Where the house sits on the property
D. Where the garage and driveway are located
What is the correct answer?
4
In an oblique drawing, equally spaced partial circles may be used to show this:
What is the correct answer?
4
These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
C. Surface or groove weld
What is the correct answer?
4
In order to convert fractional inches into decimal inches ________.
A. Look on a metric conversion chart
B. Divide the numerator (top number) by the denominator (bottom number)
C. Check the engineer's scale
What is the correct answer?
4
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
What is the correct answer?
4
In oblique sketches, the most commonly used angles for receding lines are:
What is the correct answer?
4
In working drawings, these show all necessary information not given directly on the drawing with its dimensions and notes:
D. Title and record strips
What is the correct answer?
4
The first step in creating a traditional technical drawing is to ________.
A. Draw a series of guide lines
C. Align the paper so that it will be positioned square to the parallel bar
D. Sharpen the leads in the technical pens
What is the correct answer?
4
Geometric primitives include shapes such as ________.
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
What is the correct answer?
4
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
What is the correct answer?
4
The dimension text size is determined by what the architect deems necessary in __________.
What is the correct answer?
4
The second line of dimensions out from the plan generally includes ________.
A. Centers of doors and windows
B. The distances between outside walls and interior walls
C. The measurement from the outside of the brick to the inside of the exterior wall
D. The measurement from one outside corner to the opposite outside corner
What is the correct answer?
4
Objects that are symmetric can be shown effectively using this type of section:
What is the correct answer?
4
The UCS icon represents the intersection of the ________.
What is the correct answer?
4
Technical drawings typically serve one of three purposes:
A. Visualization, Communication, or Documentation
B. Visualization, Dimensioning, or Documentation
C. Communication, Documentation, or Installation
D. Documentation, Installation, or Engineering
What is the correct answer?
4
In architectural drawing ________ are often used to illustrate and detail structural components.
A. Foundation beam detail sections
What is the correct answer?
4
Approximately this much of the cost of product development and manufacture is determined at the design stage:
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
Welding drawings are a special type of this kind of drawing: