Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
Door openings and walls
Centers of cabinets
Windows
All of the above
Correct Answer :
A. Door openings and walls
Related Questions
Geometric primitives include shapes such as ________.
Boxes
Cylinders
Wedges
All of the above
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
Client
CAD trainee
Receptionist
Checker
When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
Horizontal
Vertical
Inclined
None of the above
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
Foreshortened
Parallel
Orthographic
Oblique
This is the term for the range of tightness or looseness resulting from the allowances and tolerances in mating parts:
Limits
Fit
Specifications
Allowance
In perspective drawings this is placed between the observer and the object:
Vanishing point / horizon
Station point
Ground line
Plane of projection / picture plane
In oblique sketches, the most commonly used angles for receding lines are:
15 or 30 degrees
25 or 30 degrees
30 or 45 degrees
45 or 60 degrees
The maximum and minimum sizes of a feature are identified by a ________ tolerance.
Limits
GD&T
Reference
Allowance
The top, front, and bottom views align in this manner:
Horizontally
Vertically
According to the planar views
Parallel to the frontal plane
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
Aggregate
Pre-stressed
Reinforced
Preloaded
The site plan illustrates ________.
The floor plan
Where the house sits on the property
The roof plan
Where the garage and driveway are located
This is the intersection of the ground plane with the picture plane:
Vanishing point
Ground line
Station point
Horizon
Once a drawing is determined to be complete, the title block is used to document the change from:
A draft to a finished drawing
A finished to a working drawing
An assembly to a finished drawing
A working drawing to a draft
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
Circular
Elliptical
Lengthened
Angular
9.The lines used to create the auxiliary view should appear as ________ in the finished view.
Object lines
Construction lines
Reference lines
Construction lines
The foundation contractor will work with the following architectural plans.
Foundation
Site plan
Floor plan
All of the above
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
Planar
Horizontal
Auxiliary
Orthographic
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
Object
Hidden
Center
Phantom
These are vertical distances above a common datum, reference plane, or point:
Plats
Elevations
Traverse
Profiles
This type of solid has two bases that are parallel equal polygons:
Pyramid
Prism
Cone
Torus
In isometric projection, all distances are approximately this percentage of their true size:
120 percent
80 percent
50 percent
20 percent
The edges of a cube in isometric projection make angles of this many degrees with each other:
30
60
90
120
3.When lines intersect on a drawing at angles of this many degrees, it is customary not to dimension the angle:
360
180
90
45
The Press-Pull tool will ________ the face of a solid model in the direction it faces.
Taper
Extrude
Spiral
None of the above
In working drawings, these show all necessary information not given directly on the drawing with its dimensions and notes:
Document strips
Portable documents
Formatting forms
Title and record strips
Most architectural drawings produced for field use by building contractors are printed on architectural D size paper which measures ________.
24 × 36
18 × 24
11 × 17
34 × 22
The title block used on working drawings should include the __________.
Sheet number
Line type
Layer set
All of the above
Before starting an isometric drawing in Auto-CAD the drafter needs to ________.
Set the grid to isometric
Set the current layer to Defpoints
Turn Object Snap off
Turn Ortho off
This is used in applications for nonferrous construction:
Copper tubing
Steel pipe
PVC pipe
Iron tubing
This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process:
Traditional engineering design
The manufacturing process
Concurrent design
Design for recycling