A cylinder can be created by drawing a rectangular shape then the ________ tool.
Revolve
Sweep
Extrude
None of the above
Correct Answer :
A. Revolve
Related Questions
This type of drawing shows two lines representing the pipe diameter:
Single-line
Double-line
Standard piping
Centerline piping
When creating a block the drafter needs to pay particular attention to selecting a base point because it determines the ________.
Scale
Rotation angle
Insertion point
Color
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
These are used to attach parts to a cylinder so they won't turn on it:
Lugs and bearings
Key-seats and bearings
Knurls and keys
Keys and keyways/key-seats
When filling an area with a hatch pattern in Auto-CAD the drafter needs to be able to ________.
See the entire bounding area to hatch
Set Ortho on
Turn ISO grid off
Set the layer to Defpoints
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
A cutting plane line
Section lining
Visible lines
Lines and arrows
The text used on a typical detail sheet should be ________.
Placed horizontally
In bold text
In an architectural text style
None of the above
This should show what changes were made, when, and by whom:
Portable document
Record of revisions
Title form
Revision drawings
The second line of dimensions out from the plan generally includes ________.
Centers of doors and windows
The distances between outside walls and interior walls
The measurement from the outside of the brick to the inside of the exterior wall
The measurement from one outside corner to the opposite outside corner
These gears transmit power between shafts whose axes intersect at any angle:
Worm gears
Spur gears
Bevel gears
Racks
The edges of a cube in isometric projection make angles of this many degrees with each other:
30
60
90
120
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
Fused deposition modeling
Stereo lithography apparatus
Solid ground curing
Selective laser sintering
In an exploded assembly drawing it is customary for the drafter to use a ________ line to illustrate how parts fit together.
Phantom
Hidden
Dashed
Center
The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼ = 1'-0.
4
5
6
8
The MASSPROP shortcut will provide the following information.
Mass
Volume
Bounding box
All of the above
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
Sidewalk
Roof overhang
Plumbing drain lines
None of the above
A drafter who develops technical drawings of a highway overpass would most likely be a ________ drafter.
Architectural
Civil
Mechanical
Process piping
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
Planar
Horizontal
Auxiliary
Orthographic
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
Pull the line from away from the starting point very carefully
Insure that Ortho is on
Enter 3 for the length of the line
Read the coordinate position on the Dynamic Readout
These are special installations of stone or concrete marking the locations of points accurately determined by precise surveying:
Topographic marks
Hatches
Monuments
Pillars
Most architectural firms and mechanical design companies utilize different categories of blocks. These sets of blocks are usually housed in ________.
Block vaults
Block libraries
Block books
Block references
Placement of dimensions on a drawing is controlled by ________.
ANSI
The design engineer
Corporate drafting standards
All of the above
An accurate record of changes made to release drawings is tracked via this:
A revision block
The basic title form
Working drawings
Portable documents
These weld symbols have no arrow-side or other-side significance:
Projection or seam weld
Back or backing weld
Surface or groove weld
Flash and upset weld
In this type of section, one quarter of the object is removed:
Revolved section
Removed section
Quarter section
Half section
An Auto-CAD term that refers to a pre-drawn object which is stored in a drawing file and can be inserted into any other drawing file as needed is a ________.
Block
Brick
Balloon
None of the above
These maps are used to plan construction projects that locate construction features so they fit the topography of the area:
Subdivision plats
Landscape maps
Structural topography maps
Structure location plans
This is the range of digital or hard copy documents that specify the physical function requirements for a product:
Product design
Product definition
Drawing definition
Engineering design
The most common geometric form used in gears today is this:
Involute profile
Convolute profile
Base circle
Spur circle
These maps are used in planning installations of trees, shrubbery, drives, and other garden features:
Landscape maps
Engineering maps
Topographic maps
Cadastral maps