How would you suspend a telnet session?
CTRL-SHIFT-X 6
CTRL-SHIFT-6 X
CTRL-6 X
CTRL-C
Correct Answer :
B. CTRL-SHIFT-6 X
Related Questions
An _____________ is a public IP address associated with an inside device.
Inside global IP address
Inside local IP address
Outside global IP address
Outside local IP address
You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)
CTRL-Z
end
exit
logout
Which router command performs an overwrite process? (Choose all correct answers.)
copy running-config startup-config
copy startup-config running-config
copy tftp running-config
copy running-config tftp
RIP generates routing updates every _________ seconds.
15
30
60
90
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
Delay
Reliability
Load
Bandwidth
A ___________ is similar to a telephone circuit-switched connection.
PVC
SVC
_________ defines how the Frame Relay DTE and DCE interact with each other.
DLCI
CIR
LMI
PMI
When examining the IP routing table, an EIGRP route will be shown as what letter?
I
E
O
D
A routing protocol will use a _________ to determine which path is the best path.
Administrative distance
Metric
Hop count
Cost
OSPF uses __________ as a metric.
Bandwidth
Delay
Cost
Hop count
How many steps do LCP and NCP go through when setting up a connection?
1
2
3
4
Which control sequence moves the cursor to the end of the line?
CTRL-A
ctrl-p
ctrl-e
ctrl-z
The root switch is the one elected with the __________ __________.
Lowest MAC address
Highest MAC address
Lowest switch ID
Highest switch ID
An OSPF's router ID is based on __________.
The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
Which Frame Relay command is used to manually resolve addresses?
frame-relay interface-dlci
frame-relay map
frame-relay resolve
frame-relay lmi-type
On the 1900 switch, how do you enter User EXEC mode?
It comes up by default.
Enter the letter U in the menu.
Enter the letter K in the menu.
Enter the letter C in the menu.
EIGRP generates hellos every _________ seconds on LAN segments.
5
10
15
30
An idle DDR connection will be torn down after _________ seconds of not seeing interesting traffic.
120
122
130
132
What command assigns a User EXEC password to a 2950 switch?
password
login
enable password
enable password level
Which command takes you from Privilege EXEC mode to User EXEC mode?
enable
disable
exit
logout
Which 2950 command assigns a VLAN to an interface?
vlan-membership static
vlan
switchport access vlan
switchport mode access
The router automatically saves its configuration.
True
False
A _________ routes between different autonomous systems.
BPG
EGP
IPP
IGP
When you have configured PPP on an interface and use the show interfaces command, what state indicates the successful negotiation of a network layer protocol?
ACK
CHALLENGE
CLOSED
OPEN
What would you enter to see the last few commands you entered?
show version
show commands
show previous
show history
When configuring the ip nat inside source command, which parameter must you specify to perform PAT?
pat
overload
load
port
_________ allows you to create this summarization: 10.0.0.0/7.
Subnetting
CDR
Supernetting
VLSM
VLSM allows you to summarize __________ back to the class boundary.
Subnets
Networks
With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.
Store-and-forward
Cut-through
Fragment-free
Runtless
Which of the following are classless protocols?
IGRP
EIGRP
IGRP and EIGRP
Neither IGRP or EIGRP