Which of the following is true concerning RIPv2?
It uses triggered updates.
It uses broadcasts.
It is classful.
It doesn't support route summarization
Correct Answer :
A. It uses triggered updates.
Related Questions
How would you suspend a telnet session?
CTRL-SHIFT-X 6
CTRL-SHIFT-6 X
CTRL-6 X
CTRL-C
_________ defines how the Frame Relay DTE and DCE interact with each other.
DLCI
CIR
LMI
PMI
If the 2950's RPS is ________, the external power supply is supplying power.
Off
Amber
Flashing amber
Green
If you wanted a list of parameters for the show command, you would type ________.
LOOK
VIEW
SHOW
The function of the MODE button is to __________.
Change the status of the ports
Affect what the SYSTEM and RPS LEDs represent
Affect what the port LEDs represent
Change the status of all the LEDs
Which of the following is true concerning full-duplexing?
It can either send or receive frames, but not both simultaneously.
It can be used with hubs.
It can be used with 10Base5 cabling.
It uses point-to-point connections.
___________ only translates one (and only one) IP address to another.
NAT
PAT
PAR
NAT and PAT
A _________ provides a high-speed infrastructure to move data between storage devices and file servers.
SAN
LAN
CN
SAN and CN
RIP has a hold-down period of ____________ seconds.
60
120
180
280
A __________ topology uses a single connection to connect all devices together.
Bus
Star
Point-to-point
Ring
OSPF supports a ________-layer hierarchical design.
1
2
3
Multi
_________ has a physical star topology but a logical ring topology.
FDDI
Token Ring
Ethernet
FDDI and Token Ring
Which of the following WAN categories does ISDN fall under?
Dedicated circuit connection
Circuit-switched connection
Packet-switched connection
Which of the following is true concerning ISL?
It is supported on both the 1900 and 2950 switches.
It adds a 26-byte trailer and 4-byte header.
Tagging is done in software.
The original Ethernet frame is not modified.
Distance vector protocols use ___________ to disseminate routing information.
Unicast
Multicast
Broadcast
Which of the following trunking methods is/are proprietary to Cisco?
802.1Q
802.10
LANE
ISL
The switch port that is chosen to forward traffic for a segment is called a __________.
Root port
Alternate port
Backup port
Designated port
Which of the following is a disadvantage of SANs?
Distance limitation
Cost
Overhead
Management
You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?
1
2
3
4
The 1900 switch supports ________ VLANs.
10
32
64
250
The slot number of a 1900's Fast Ethernet uplink ports is ________.
0
1
2
No slot number is used
The default encapsulation on a synchronous serial interface is _________.
HDLC
PPP
Neither HDLC nor PPP
Which of the following is true concerning 802.1Q?
It supports hub connections.
It is supported on both the 1900 and 2950 switches.
The native VLAN is tagged.
The original Ethernet frame is not modified.
You have this binary value: 11000001. This equates to _____ in decimal.
183
193
173
203
You are given the following addressing information: 10.0.8.0/22. What type of address is this?
Network
Directed Broadcast
Host
An OSPF's router ID is based on __________.
The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
RIP generates routing updates every _________ seconds.
15
30
60
90
Which controller command specifies how ones and zeros are represented on a digital circuit?
framing
linecode
clock source
interface
What uses 64 Kbps of bandwidth?
PRI
BRI
DS1
DS0
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI