IGRP generates an update every ___________ seconds.
30
60
90
120
Correct Answer :
C. 90
Related Questions
Which of the following is true concerning ACLs?
Order of the statements is automatic.
All statements are processed.
If no match is found, the packet is permitted.
You can delete a specific statement in a named list.
With a crossover cable, which pins are crossed over?
1 and 2, 3 and 6
1 and 3, 2 and 6
1 and 4, 2 and 6
1 and 3, 4 and 6
RIP generates routing updates every _________ seconds.
15
30
60
90
Which router command would take you back to a suspended telnet session?
reconnect
connect
resume
toggle
How would you suspend a telnet session?
CTRL-SHIFT-X 6
CTRL-SHIFT-6 X
CTRL-6 X
CTRL-C
Which prompt indicates that you are at User EXEC mode?
>
#
%
@
Which of the following is true concerning bridges?
They switch frames in hardware.
They support half- and full-duplexing.
They support one collision domain for the entire bridge.
They do only store-and-forward switching.
Extended traceroute works from which mode?
User EXEC
Privilege EXEC
Configuration
User and Privilege EXEC
Which of the following is a disadvantage of SANs?
Distance limitation
Cost
Overhead
Management
Which 2950 command assigns a VLAN to an interface?
vlan-membership static
vlan
switchport access vlan
switchport mode access
BPDU stands for ____________.
Bridge Protocol Description Unicast
Bridge Protocol Data Unit
Bridge Protocol Description Unit
Bridge Protocol Data Unicast
Which of the following situations are best for DDR connections?
Primary WAN connection
A lot of constant traffic
Long phone calls
Backup connection
A _________ uses Gigabit Ethernet as a media type
WAN
LAN
MAN
LAN and MAN
With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.
Store-and-forward
Cut-through
Fragment-free
Runtless
Which is an example of a hybrid protocol?
IGRP
EIGRP
RIPv1
OSPF
When choosing a networking product, you should consider all of the following except _______.
Ease of installation and support
Product features and functions
Backplane capacity
Amount of memory
Which command activates an IP ACL on a router's interface?
access-list
ip access-group
access-class
access-group
OSPF uses __________ as a metric.
Bandwidth
Delay
Cost
Hop count
Which type of traffic is sent to a group of devices?
Multicast
Unicast
Broadcast
Groupcast
Which of the following is true concerning RIPv2?
It uses triggered updates.
It uses broadcasts.
It is classful.
It doesn't support route summarization
Which Frame Relay command is used to manually resolve addresses?
frame-relay interface-dlci
frame-relay map
frame-relay resolve
frame-relay lmi-type
Which 2950 command enables trunking?
switchport mode trunk
trunking on
trunking enable
switchport trunk on
You are given a Class C network with a subnet mask of 255.255.255.248. How many host addresses are there on each subnet?
4
6
8
14
The _________ command takes you from User EXEC mode to Privilege EXEC mode
DISABLE
ENABLE
A ________ topology describes how devices communicate with each other.
Physical
Logical
Which router-on-a-stick command defines the VLAN for the interface?
vlan
encapsulation
trunk
frame-type
You are given the following addressing information: 10.0.8.0/22. What type of address is this?
Network
Directed Broadcast
Host
What router command saves the active configuration to NVRAM?
copy nvram startup-config
copy startup-config running-config
copy running-config nvram
copy running-config startup-config
You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)
CTRL-Z
end
exit
logout
Your router is running RIP and OSPF and both routing protocols are learning 192.168.1.0/24. Which routing protocol will your router use for this route?
RIP
OSPF