Related Questions
What is the correct answer?
4
This type of drawing shows two lines representing the pipe diameter:
What is the correct answer?
4
The thread note for a typical bolt will include the ________.
A. Major diameter of the thread
What is the correct answer?
4
The type of line that projects from an object for the express purpose of locating a dimension is a ________ line.
What is the correct answer?
4
In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
What is the correct answer?
4
This is the measured size of a finished part:
What is the correct answer?
4
Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.
What is the correct answer?
4
3.When lines intersect on a drawing at angles of this many degrees, it is customary not to dimension the angle:
What is the correct answer?
4
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
What is the correct answer?
4
In isometric projection, all distances are approximately this percentage of their true size:
What is the correct answer?
4
The MASSPROP shortcut will provide the following information.
What is the correct answer?
4
This is how axonometric, oblique, and perspective sketches show objects:
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
Which of the following is one of the basic types of welded joints:
What is the correct answer?
4
The bounding box method for setting up an isometric drawing helps the drafter ________.
A. Confine the isometric drawing to its maximum size
B. Figure what lines are to be illustrated vertical and horizontal
C. Position the isometric drawing in paper space
What is the correct answer?
4
A cylinder can be created by drawing a rectangular shape then the ________ tool.
What is the correct answer?
4
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
A. Right to left and top to bottom
B. Right to left and bottom to top
C. Left to right and top to bottom
D. Left to right and bottom to top
What is the correct answer?
4
A secondary auxiliary view is a projection off of the ________.
C. Primary auxiliary view
What is the correct answer?
4
These maps are used to plan construction projects that locate construction features so they fit the topography of the area:
C. Structural topography maps
D. Structure location plans
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
In an assembly section, these parts should have their section lines left out or shown solid black:
What is the correct answer?
4
In order to create an accurate assembly drawing the drafter should create the ________ drawings first.
What is the correct answer?
4
The distance a screw thread advances axially in one turn is the:
What is the correct answer?
4
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
B. Perpendicular projection
What is the correct answer?
4
Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
What is the correct answer?
4
When only a small section of an interior area needs to be revealed the drafter can use a ________ section.
What is the correct answer?
4
This process recognizes the inherent interrelationships between design and manufacturing:
A. Design for manufacture
B. Design for manufacture and assembly
C. Design for concurrent engineering
What is the correct answer?
4
The principle views associated with orthographic projection are ________.
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
A. Rotate the snap grid to the same angle of the inclined plane
B. Offset the right vertical line of the front view
C. Rotate the top line of the front view 45 degrees
D. Offset the top line of the front view 2 inches