Related Questions
What is the correct answer?
4
The typical parts list should include the ________.
B. Manufacturing material
C. Number of parts needed
What is the correct answer?
4
The site plan illustrates ________.
B. Where the house sits on the property
D. Where the garage and driveway are located
What is the correct answer?
4
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
What is the correct answer?
4
When dimensioning piping drawings, you give the lengths of all runs of this type:
What is the correct answer?
4
This process recognizes the inherent interrelationships between design and manufacturing:
A. Design for manufacture
B. Design for manufacture and assembly
C. Design for concurrent engineering
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane:
What is the correct answer?
4
The default position of the UCS icon is positioned at ________ on the AutoCAD grid.
What is the correct answer?
4
It is customary for the first sheet of a working drawing set to include ________.
What is the correct answer?
4
Some of the common terms used to describe technical drawing include:
What is the correct answer?
4
These are lines drawn on a map to locate, in the plan view, points of equal ground elevation:
What is the correct answer?
4
This allows the performance of structures to be analyzed and tested efficiently, accurately, and quickly:
A. Computer-aided manufacturing
C. Computer-aided engineering
D. Computer-aided prototyping
What is the correct answer?
4
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
What is the correct answer?
4
The text used on a typical detail sheet should be ________.
C. In an architectural text style
What is the correct answer?
4
In this type of dimensioning, allowance must be made for bends:
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a ________.
C. Whole new set of drawings
What is the correct answer?
4
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
What is the correct answer?
4
These types of projectors converge at a vanishing point:
What is the correct answer?
4
The Offset tool should only be used for placing ________ in an isometric drawing.
What is the correct answer?
4
Elevation drawings will include information about ________.
What is the correct answer?
4
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
A. Right to left and top to bottom
B. Right to left and bottom to top
C. Left to right and top to bottom
D. Left to right and bottom to top
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
These units are based on inch-foot and yard measurements:
A. International customary units
D. ISO international units
What is the correct answer?
4
This is an angled surface used on cylinders to make them easier to handle:
What is the correct answer?
4
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
What is the correct answer?
4
Approximately this much of the cost of product development and manufacture is determined at the design stage:
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane:
What is the correct answer?
4
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
C. Use the left view instead
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
The dimension text size is determined by what the architect deems necessary in __________.